Формат FXT файла версии 405

 

Как можно найти формат FXT файла версии 405?

Последнее упоминание нашел версии 404.

 

А я не хочу его сам создавать. Я хочу его прочитать...
 

ja ispolzuju etot rasklad


header - 728 byte,

tick - 52 byte


#ifdef _WIN32
#pragma pack(push, 8)
#else
#pragma pack(8)
#endif // _WIN32

//+------------------------------------------------------------------+
//| |
//+------------------------------------------------------------------+
typedef struct tagTestHistoryHeader
{
int version; // 405
char copyright[64]; // copyright
char description[128];
//---- general parameters
char currency[12]; // currency base

int period;
int model; // for what modeling type was the ticks sequence generated
int bars; // amount of bars in history
time_t fromdate; // ticks generated from this date
time_t todate; // ticks generating stopped at this date
double modelquality; // modeling quality
int totalticks; //??
int unknown2;
int unknown3;

int spread; // ? ??? ??? ????? ???? ????????? ????? - ???? ???????????? ??????? ???????????!
int digits;
double point;
int lot_min; // minimum lot size
int lot_max; // maximum lot size
int lot_step;
int stops_level; // stops level value
int gtc_pendings; // instruction to close pending orders at the end of day
//---- profit calculation parameters
double contract_size; // contract size
//int unknown6;
double tick_value; // value of one tick
double tick_size; // size of one tick
int profit_mode; // profit calculation mode { PROFIT_CALC_FOREX, PROFIT_CALC_CFD, PROFIT_CALC_FUTURES }
//---- swap calculation
int swap_enable; // enable swap
int swap_type; // type of swap { SWAP_BY_POINTS, SWAP_BY_DOLLARS, SWAP_BY_INTEREST }
double swap_long;
double swap_short; // swap overnight value
int swap_rollover3days; // three-days swap rollover
//---- margin calculation
int leverage; // leverage
int free_margin_mode; // free margin calculation mode { MARGIN_DONT_USE, MARGIN_USE_ALL, MARGIN_USE_PROFIT, MARGIN_USE_LOSS }
int margin_mode; // margin calculation mode { MARGIN_CALC_FOREX,MARGIN_CALC_CFD,MARGIN_CALC_FUTURES,MARGIN_CALC_CFDINDEX };
int margin_stopout; // margin stopout level
int margin_stopout_mode;// stop out check mode { MARGIN_TYPE_PERCENT, MARGIN_TYPE_CURRENCY }
double margin_initial; // margin requirements
double margin_maintenance; // margin maintenance requirements
double margin_hedged; // margin requirements for hedged positions
double margin_divider; // margin divider
char margin_currency[12];// margin currency
//---- commission calculation
double comm_base; // basic commission
int comm_type; // basic commission type { COMM_TYPE_MONEY, COMM_TYPE_PIPS, COMM_TYPE_PERCENT }
int comm_lots; // commission per lot or per deal { COMMISSION_PER_LOT, COMMISSION_PER_DEAL }
//---- for internal use
int from_bar; // fromdate bar number
int to_bar; // todate bar number
int start_period[6]; // number of bar at which the smaller period modeling started
int set_from; // begin date from tester settings
int set_to; // end date from tester settings
//----
int freeze_level; // order's freeze level in points
//----
int reserved[60];
} TestHistoryHeader, *lpTestHistoryHeader;

#ifdef _WIN32
#pragma pack(pop)
#pragma pack(push, 1)
#else
#pragma pack()
#pragma pack(1)
#endif // _WIN32

typedef struct tagTestHistory
{
time_t otm; // bar time
double open; // OHLCV value
double low;
double high;
double close;
double volume;
time_t ctm; // bar work time
int flag; // exper flag 0-bar is modified, but expert is not run
} TestHistory, *lpTestHistory;

#ifdef _WIN32
#pragma pack(pop)
#else
#pragma pack()
#endif // _WIN32

 
Rilin:

А я не хочу его сам создавать. Я хочу его прочитать...

а в чем смысл читать его ?

 
YuraZ:
Rilin:

А я не хочу его сам создавать. Я хочу его прочитать...

а в чем смысл читать его ?


Ja, naprimer, xociu sdelat tester pod linux isplzuja mt4 podgotovlenije faili

Причина обращения: